Skip to content Skip to navigation Skip to collection information

Connexions

You are here: Home » Content » Information and Signal Theory » Decibel scale with signal processing applications

Navigation

Recently Viewed

This feature requires Javascript to be enabled.
 

Decibel scale with signal processing applications

Module by: Anders Gjendemsjø. E-mail the author

Summary: Introduces the decibel scale and shows typical calculations for signal processing applications.

Introduction

The concept of decibel originates from telephone engineers who were working with power loss in a telephone line consisting of cascaded circuits. The power loss in each circuit is the ratio of the power in to the power out, or equivivalently, the power gain is the ratio of the power out to the power in.

Let PinPin be the power input to a telephone line and PoutPout the power out. The power gain is then given by

Gain=PoutPin Gain Pout Pin
(1)
Taking the logarithm of the gain formula we obtain a comparative measure called Bel.

Bel:

Gain⁢Bel=logPoutPin Gain Bel 10 Pout Pin
This measure is in honour of Alexander G. Bell, see Figure 1.

Figure 1: Alexander G. Bell
Figure 1 (agbell.jpg)

Decibel

Bel is often a to large quantity, so we define a more useful measure, decibel:

Gain⁢dB=10⁢logPoutPin Gain dB 10 10 Pout Pin
(2)
Please note from the definition that the gain in dB is relative to the input power. In general we define:
Number of decibels=10⁢logPPref Number of decibels 10 10 P Pref
(3)

If no reference level is given it is customary to use Pref=1 W Pref 1 W , in which case we have:

Decibel:

Number of decibels=10⁢logP Number of decibels 10 10 P

Example 1

Given the power spectrum density (psd) function of a signal x⁢nxn, Sxx⁢j⁢f Sxx f . Express the magnitude of the psd in decibels.

We find Sxx⁢dB=10⁢log|Sxx⁢j⁢f| Sxx dB 10 10 Sxx f .

More about decibels

Above we’ve calculated the decibel equivalent of power. Power is a quadratic variable, whereas voltage and current are linear variables. This can be seen, for example, from the formulas P=V2R P V 2 R and P=I2⁢R P I 2 R .

So if we want to find the decibel value of a current or voltage, or more general an amplitude we use:

Amplitude⁢dB=20⁢logAmplitudeAmplituderef Amplitude dB 20 10 Amplitude Amplituderef
(4)
This is illustrated in the following example.

Example 2

Express the magnitude of the filter H⁢j⁢f H f in dB scale.

The magnitude is given by |H⁢j⁢f| H f , which gives: |H⁢dB|=20⁢log|H⁢j⁢f| H dB 20 10 H f .

Plots of the magnitude of an example filter |H⁢j⁢f| H f and its decibel equivalent are shown in Figure 2.

Figure 2: Magnitude responses.
Figure 2 (filters.png)

Some basic arithmetic

The ratios 1,10,100, 1000 give dB values 0 dB, 10 dB, 20 dB and 30 dB respectively. This implies that an increase of 10 dB corresponds to a ratio increase by a factor 10.

This can easily be shown: Given a ratio R we have R[dB] = 10 log R. Increasing the ratio by a factor of 10 we have: 10 log (10*R) = 10 log 10 + 10 log R = 10 dB + R dB.

Another important dB-value is 3dB. This comes from the fact that:

An increase by a factor 2 gives: an increase of 10 log 2 ≈ 3 dB. A “increase” by a factor 1/2 gives: an “increase” of 10 log 1/2 ≈ -3 dB.

Example 3

In filter terminology the cut-off frequency is a term that often appears. The cutoff frequency (for lowpass and highpass filters), fcfc, is the frequency at which the squared magnitude response in dB is ½. In decibel scale this corresponds to about -3 dB.

Decibels in linear systems

In signal processing we have the following relations for linear systems:

Y⁢j⁢f=H⁢j⁢f⁢X⁢j⁢f Y f H f X f
(5)
where X and H denotes the input signal and the filter respectively. Taking absolute values on both sides of Equation 5 and converting to decibels we get:

Input and output relations for linear systems:

The output amplitude at a given frequency is simply given by the sum of the filter gain and the input amplitude, both in dB.

Other references:

Above we have used Pref=1 W Pref 1 W as a reference and obtained the standard dB measure. In some applications it is more useful to use Pref=1 mW Pref 1 mW and we then have the dBm measure.

Another example is when calculating the gain of different antennas. Then it is customary to use an isotropic (equal radiation in all directions) antenna as a reference. So for a given antenna we can use the dBi measure. (i -> isotropic)

Matlab files

filter_example.m

Collection Navigation

Content actions

Download module as:

PDF | More downloads ...

Add:

Collection to:

My Favorites (?)

'My Favorites' is a special kind of lens which you can use to bookmark modules and collections. 'My Favorites' can only be seen by you, and collections saved in 'My Favorites' can remember the last module you were on. You need an account to use 'My Favorites'.

| A lens I own (?)

Definition of a lens

Lenses

A lens is a custom view of the content in the repository. You can think of it as a fancy kind of list that will let you see content through the eyes of organizations and people you trust.

What is in a lens?

Lens makers point to materials (modules and collections), creating a guide that includes their own comments and descriptive tags about the content.

Who can create a lens?

Any individual member, a community, or a respected organization.

What are tags? tag icon

Tags are descriptors added by lens makers to help label content, attaching a vocabulary that is meaningful in the context of the lens.

| External bookmarks

Module to:

My Favorites (?)

'My Favorites' is a special kind of lens which you can use to bookmark modules and collections. 'My Favorites' can only be seen by you, and collections saved in 'My Favorites' can remember the last module you were on. You need an account to use 'My Favorites'.

| A lens I own (?)

Definition of a lens

Lenses

A lens is a custom view of the content in the repository. You can think of it as a fancy kind of list that will let you see content through the eyes of organizations and people you trust.

What is in a lens?

Lens makers point to materials (modules and collections), creating a guide that includes their own comments and descriptive tags about the content.

Who can create a lens?

Any individual member, a community, or a respected organization.

What are tags? tag icon

Tags are descriptors added by lens makers to help label content, attaching a vocabulary that is meaningful in the context of the lens.

| External bookmarks