Skip to content Skip to navigation

OpenStax-CNX

You are here: Home » Content » Bernoulli’s Equation

Navigation

Recently Viewed

This feature requires Javascript to be enabled.

Tags

(What is a tag?)

These tags come from the endorsement, affiliation, and other lenses that include this content.
 

Bernoulli’s Equation

Module by: OpenStax College. E-mail the author

Summary:

  • Explain the terms in Bernoulli’s equation.
  • Explain how Bernoulli’s equation is related to conservation of energy.
  • Explain how to derive Bernoulli’s principle from Bernoulli’s equation.
  • Calculate with Bernoulli’s principle.
  • List some applications of Bernoulli’s principle.

Note: You are viewing an old version of this document. The latest version is available here.

When a fluid flows into a narrower channel, its speed increases. That means its kinetic energy also increases. Where does that change in kinetic energy come from? The increased kinetic energy comes from the net work done on the fluid to push it into the channel and the work done on the fluid by the gravitational force, if the fluid changes vertical position. Recall the work-energy theorem,

Wnet=12mv212 mv02.Wnet=12mv212 mv02.
(1)

There is a pressure difference when the channel narrows. This pressure difference results in a net force on the fluid: recall that pressure times area equals force. The net work done increases the fluid’s kinetic energy. As a result, the pressure will drop in a rapidly-moving fluid, whether or not the fluid is confined to a tube.

There are a number of common examples of pressure dropping in rapidly-moving fluids. Shower curtains have a disagreeable habit of bulging into the shower stall when the shower is on. The high-velocity stream of water and air creates a region of lower pressure inside the shower, and standard atmospheric pressure on the other side. The pressure difference results in a net force inward pushing the curtain in. You may also have noticed that when passing a truck on the highway, your car tends to veer toward it. The reason is the same—the high velocity of the air between the car and the truck creates a region of lower pressure, and the vehicles are pushed together by greater pressure on the outside. (See Figure 1.) This effect was observed as far back as the mid-1800s, when it was found that trains passing in opposite directions tipped precariously toward one another.

Figure 1: An overhead view of a car passing a truck on a highway. Air passing between the vehicles flows in a narrower channel and must increase its speed (v2v2 size 12{v rSub { size 8{2} } } {} is greater than v1v1 size 12{v rSub { size 8{1} } } {}), causing the pressure between them to drop (PiPi size 12{P rSub { size 8{i} } } {} is less than PoPo size 12{P rSub { size 8{o} } } {}). Greater pressure on the outside pushes the car and truck together.
An overhead view of a car passing by a truck on a highway toward left is shown. The air passing through the vehicles is shown using lines along the length of both the vehicles. The lines representing the air movement has a velocity v one outside the area between the vehicles and velocity v two between the vehicles. v two is shown to be greater than v one with the help of a longer arrow toward right. The pressure between the car and the truck is represented by P i and the pressure at the other ends of both the vehicles is represented as P zero. The pressure P i is shown to be less than P zero by shorter length of the arrow. The direction of P i is shown as pushing the car and truck apart, and the direction of P zero is shown as pushing the car and truck toward each other.

Making Connections: Take-Home Investigation with a Sheet of Paper:

Hold the short edge of a sheet of paper parallel to your mouth with one hand on each side of your mouth. The page should slant downward over your hands. Blow over the top of the page. Describe what happens and explain the reason for this behavior.

Bernoulli’s Equation

The relationship between pressure and velocity in fluids is described quantitatively by Bernoulli’s equation, named after its discoverer, the Swiss scientist Daniel Bernoulli (1700–1782). Bernoulli’s equation states that for an incompressible, frictionless fluid, the following sum is constant:

P+12ρv2+ρgh=constant,P+12ρv2+ρgh=constant, size 12{P+ { {1} over {2} } ρv rSup { size 8{2} } +ρ ital "gh"="constant,"} {}
(2)

where PP size 12{P} {} is the absolute pressure, ρρ size 12{ρ} {} is the fluid density, vv size 12{v} {} is the velocity of the fluid, hh size 12{h} {} is the height above some reference point, and gg size 12{g} {} is the acceleration due to gravity. If we follow a small volume of fluid along its path, various quantities in the sum may change, but the total remains constant. Let the subscripts 1 and 2 refer to any two points along the path that the bit of fluid follows; Bernoulli’s equation becomes

P 1 + 1 2 ρv 1 2 + ρ gh 1 = P 2 + 1 2 ρv 2 2 + ρ gh 2 . P 1 + 1 2 ρv 1 2 + ρ gh 1 = P 2 + 1 2 ρv 2 2 + ρ gh 2 . size 12{P rSub { size 8{1} } + { {1} over {2} } ρv rSub { size 8{1} } "" lSup { size 8{2} } +ρ ital "gh" rSub { size 8{1} } =P rSub { size 8{2} } + { {1} over {2} } ρv rSub { size 8{2} } "" lSup { size 8{2} } +ρ ital "gh" rSub { size 8{2} } "." } {}
(3)

Bernoulli’s equation is a form of the conservation of energy principle. Note that the second and third terms are the kinetic and potential energy with mm size 12{m} {} replaced by ρρ size 12{ρ} {}. In fact, each term in the equation has units of energy per unit volume. We can prove this for the second term by substituting ρ=m/Vρ=m/V size 12{ρ=m/V} {} into it and gathering terms:

12ρv2=12mv2V=KEV.12ρv2=12mv2V=KEV. size 12{ { {1} over {2} } ρv rSup { size 8{2} } = { { { {1} over {2} } ital "mv" rSup { size 8{2} } } over {V} } = { {"KE"} over {V} } "."} {}
(4)

So 12ρv212ρv2 size 12{ { { size 8{1} } over { size 8{2} } } ρv rSup { size 8{2} } } {} is the kinetic energy per unit volume. Making the same substitution into the third term in the equation, we find

ρgh=mghV=PEgV,ρgh=mghV=PEgV, size 12{ρ ital "gh"= { { ital "mgh"} over {V} } = { {"PE" rSub { size 8{"g"} } } over {V} } "."} {}
(5)

so ρ ghρ gh size 12{ρ ital "gh"} {} is the gravitational potential energy per unit volume. Note that pressure PP size 12{P} {} has units of energy per unit volume, too. Since P=F/AP=F/A size 12{P=F/A} {}, its units are N/m2N/m2 size 12{"N/m" rSup { size 8{2} } } {}. If we multiply these by m/m, we obtain Nm/m3=J/m3Nm/m3=J/m3 size 12{N cdot "m/m" rSup { size 8{3} } ="J/m" rSup { size 8{3} } } {}, or energy per unit volume. Bernoulli’s equation is, in fact, just a convenient statement of conservation of energy for an incompressible fluid in the absence of friction.

Making Connections: Conservation of Energy:

Conservation of energy applied to fluid flow produces Bernoulli’s equation. The net work done by the fluid’s pressure results in changes in the fluid’s KEKE size 12{"KE"} {} and PEgPEg size 12{"PE" rSub { size 8{g} } } {} per unit volume. If other forms of energy are involved in fluid flow, Bernoulli’s equation can be modified to take these forms into account. Such forms of energy include thermal energy dissipated because of fluid viscosity.

The general form of Bernoulli’s equation has three terms in it, and it is broadly applicable. To understand it better, we will look at a number of specific situations that simplify and illustrate its use and meaning.

Bernoulli’s Equation for Static Fluids

Let us first consider the very simple situation where the fluid is static—that is, v1=v2=0v1=v2=0 size 12{v rSub { size 8{1} } =v rSub { size 8{2} } =0} {}. Bernoulli’s equation in that case is

P1+ρgh1=P2+ρgh2.P1+ρgh1=P2+ρgh2. size 12{P rSub { size 8{1} } +ρ ital "gh" rSub { size 8{1} } =P rSub { size 8{2} } +ρ ital "gh" rSub { size 8{2} } "."} {}
(6)

We can further simplify the equation by taking h2=0h2=0 size 12{h rSub { size 8{2} } =0} {} (we can always choose some height to be zero, just as we often have done for other situations involving the gravitational force, and take all other heights to be relative to this). In that case, we get

P2=P1+ρgh1.P2=P1+ρgh1. size 12{P rSub { size 8{2} } =P rSub { size 8{1} } +ρ ital "gh" rSub { size 8{1} } "."} {}
(7)

This equation tells us that, in static fluids, pressure increases with depth. As we go from point 1 to point 2 in the fluid, the depth increases by h1h1 size 12{h rSub { size 8{1} } } {}, and consequently, P2P2 size 12{P rSub { size 8{2} } } {} is greater than P1P1 size 12{P rSub { size 8{1} } } {} by an amount ρgh1ρgh1 size 12{ρ ital "gh" rSub { size 8{1} } } {}. In the very simplest case, P1P1 size 12{P rSub { size 8{1} } } {} is zero at the top of the fluid, and we get the familiar relationship P=ρghP=ρgh size 12{P=ρ ital "gh"} {}. (Recall that P=ρghP=ρgh size 12{P=hρg} {} and ΔPEg=mgh.ΔPEg=mgh. size 12{Δ"PE" rSub { size 8{g} } = ital "mgh"} {}) Bernoulli’s equation includes the fact that the pressure due to the weight of a fluid is ρghρgh size 12{ρ ital "gh"} {}. Although we introduce Bernoulli’s equation for fluid flow, it includes much of what we studied for static fluids in the preceding chapter.

Bernoulli’s Principle—Bernoulli’s Equation at Constant Depth

Another important situation is one in which the fluid moves but its depth is constant—that is, h1=h2h1=h2 size 12{h rSub { size 8{1} } =h rSub { size 8{2} } } {}. Under that condition, Bernoulli’s equation becomes

P 1 + 1 2 ρv 1 2 = P 2 + 1 2 ρv 2 2 . P 1 + 1 2 ρv 1 2 = P 2 + 1 2 ρv 2 2 . size 12{P rSub { size 8{1} } + { {1} over {2} } ρv rSub { size 8{1} } "" lSup { size 8{2} } =P rSub { size 8{2} } + { {1} over {2} } ρv rSub { size 8{2} } "" lSup { size 8{2} } "." } {}
(8)

Situations in which fluid flows at a constant depth are so important that this equation is often called Bernoulli’s principle. It is Bernoulli’s equation for fluids at constant depth. (Note again that this applies to a small volume of fluid as we follow it along its path.) As we have just discussed, pressure drops as speed increases in a moving fluid. We can see this from Bernoulli’s principle. For example, if v2v2 size 12{v rSub { size 8{2} } } {} is greater than v1v1 size 12{v rSub { size 8{1} } } {} in the equation, then P2P2 size 12{P rSub { size 8{2} } } {} must be less than P1P1 size 12{P rSub { size 8{1} } } {} for the equality to hold.

Example 1: Calculating Pressure: Pressure Drops as a Fluid Speeds Up

In (Reference), we found that the speed of water in a hose increased from 1.96 m/s to 25.5 m/s going from the hose to the nozzle. Calculate the pressure in the hose, given that the absolute pressure in the nozzle is 1.01×105N/m21.01×105N/m2 size 12{1 "." "01" times "10" rSup { size 8{5} } `"N/m" rSup { size 8{2} } } {} (atmospheric, as it must be) and assuming level, frictionless flow.

Strategy

Level flow means constant depth, so Bernoulli’s principle applies. We use the subscript 1 for values in the hose and 2 for those in the nozzle. We are thus asked to find P1P1 size 12{P rSub { size 8{1} } } {}.

Solution

Solving Bernoulli’s principle for P1P1 size 12{P rSub { size 8{1} } } {} yields

P 1 = P 2 + 1 2 ρv 2 2 1 2 ρv 1 2 = P 2 + 1 2 ρ ( v 2 2 v 1 2 ) . P 1 = P 2 + 1 2 ρv 2 2 1 2 ρv 1 2 = P 2 + 1 2 ρ ( v 2 2 v 1 2 ) . size 12{P rSub { size 8{1} } =P rSub { size 8{2} } + { {1} over {2} } ρv rSub { size 8{2} } "" lSup { size 8{2} } - { {1} over {2} } ρv rSub { size 8{1} } "" lSup { size 8{2} } =P rSub { size 8{2} } + { {1} over {2} } ρ \( v rSub { size 8{2} } "" lSup { size 8{2} } - v rSub { size 8{1} } "" lSup { size 8{2} } \) "." } {}
(9)

Substituting known values,

P1 = 1.01×105 N/m2 +12(103 kg/m3)(25.5 m/s)2(1.96 m/s)2 = 4.24×105 N/m2. P1 = 1.01×105 N/m2 +12(103 kg/m3)(25.5 m/s)2(1.96 m/s)2 = 4.24×105 N/m2.
(10)

Discussion

This absolute pressure in the hose is greater than in the nozzle, as expected since v v is greater in the nozzle. The pressure P2P2 size 12{P rSub { size 8{2} } } {} in the nozzle must be atmospheric since it emerges into the atmosphere without other changes in conditions.

Applications of Bernoulli’s Principle

There are a number of devices and situations in which fluid flows at a constant height and, thus, can be analyzed with Bernoulli’s principle.

Entrainment

People have long put the Bernoulli principle to work by using reduced pressure in high-velocity fluids to move things about. With a higher pressure on the outside, the high-velocity fluid forces other fluids into the stream. This process is called entrainment. Entrainment devices have been in use since ancient times, particularly as pumps to raise water small heights, as in draining swamps, fields, or other low-lying areas. Some other devices that use the concept of entrainment are shown in Figure 2.

Figure 2: Examples of entrainment devices that use increased fluid speed to create low pressures, which then entrain one fluid into another. (a) A Bunsen burner uses an adjustable gas nozzle, entraining air for proper combustion. (b) An atomizer uses a squeeze bulb to create a jet of air that entrains drops of perfume. Paint sprayers and carburetors use very similar techniques to move their respective liquids. (c) A common aspirator uses a high-speed stream of water to create a region of lower pressure. Aspirators may be used as suction pumps in dental and surgical situations or for draining a flooded basement or producing a reduced pressure in a vessel. (d) The chimney of a water heater is designed to entrain air into the pipe leading through the ceiling.
Part a of the figure shows a rectangular section of a cylindrical Bunsen burner as a vertical column. The natural gas is shown to enter the rectangular column from the bottom upward. The air is shown to enter though a nozzle at the left side near the bottom part of the rectangular column and rise upward. Both air and natural gas are shown to rise up together along the length of the column, shown as vertical arrows along the length pointing upward. Part b of the figure shows an atomizer that uses a squeeze bulb in the shape of a small sphere to create a jet of air that entrains drops of perfume contained in a spherical bottomed container. The air is shown to come out of the squeeze bulb and the perfume is shown to rise up from the spherical bottomed container. Part c of the figure shows a common aspirator which contains a cylindrical tube held vertically. The tube is broader on the top and narrow at the bottom. Water is shown to enter the tube from the broader region and flow toward the narrow region. Air is shown to enter the cylindrical tube from the bottom part of the broader side and also flow toward the narrow tube. Part d of the figure shows the chimney of a water heater. Water heater is shown as a rectangular box at the bottom having a cylindrical section in the middle. The cylindrical section is broader at the bottom and narrow toward the top. Hot air is shown to rise up along the vertical section of the cylindrical tube. The chimney is conical at the bottom and rectangular upward and is shown above the rectangular water heater. The hot air enters the chimney at the conical end and rises upward. Cool air is shown to enter the chimney through the area between the rectangular section of heater and chimney from the two sides and rise up along the chimney with the hot air as shown by vertical arrows.

Wings and Sails

The airplane wing is a beautiful example of Bernoulli’s principle in action. Figure 3(a) shows the characteristic shape of a wing. The wing is tilted upward at a small angle and the upper surface is longer, causing air to flow faster over it. The pressure on top of the wing is therefore reduced, creating a net upward force or lift. (Wings can also gain lift by pushing air downward, utilizing the conservation of momentum principle. The deflected air molecules result in an upward force on the wing — Newton’s third law.) Sails also have the characteristic shape of a wing. (See Figure 3(b).) The pressure on the front side of the sail, PfrontPfront size 12{P rSub { size 8{"front"} } } {}, is lower than the pressure on the back of the sail, PbackPback size 12{P rSub { size 8{"back"} } } {}. This results in a forward force and even allows you to sail into the wind.

Making Connections: Take-Home Investigation with Two Strips of Paper:

For a good illustration of Bernoulli’s principle, make two strips of paper, each about 15 cm long and 4 cm wide. Hold the small end of one strip up to your lips and let it drape over your finger. Blow across the paper. What happens? Now hold two strips of paper up to your lips, separated by your fingers. Blow between the strips. What happens?

Velocity measurement

Figure 4 shows two devices that measure fluid velocity based on Bernoulli’s principle. The manometer in Figure 4(a) is connected to two tubes that are small enough not to appreciably disturb the flow. The tube facing the oncoming fluid creates a dead spot having zero velocity (v1=0v1=0 size 12{v rSub { size 8{1} } =0} {}) in front of it, while fluid passing the other tube has velocity v2v2 size 12{v rSub { size 8{2} } } {}. This means that Bernoulli’s principle as stated in P 1 + 1 2 ρv 1 2 = P 2 + 1 2 ρv 2 2 P 1 + 1 2 ρv 1 2 = P 2 + 1 2 ρv 2 2 size 12{P rSub { size 8{1} } + { {1} over {2} } ρv rSub { size 8{1} } "" lSup { size 8{2} } =P rSub { size 8{2} } + { {1} over {2} } ρv rSub { size 8{2} } "" lSup { size 8{2} } } {} becomes

P 1 = P 2 + 1 2 ρv 2 2 . P 1 = P 2 + 1 2 ρv 2 2 . size 12{P rSub { size 8{1} } =P rSub { size 8{2} } + { {1} over {2} } ρv rSub { size 8{2} } "" lSup { size 8{2} } "." } {}
(11)
Figure 3: (a) The Bernoulli principle helps explain lift generated by a wing. (b) Sails use the same technique to generate part of their thrust.
Part a of the figure shows a picture of a wing. It is in the form of an aerofoil. One side of the wing is broader and the other end tapers. The direction of air is shown as lines along the length of the wing. The direction of air below the wing is shown as flowing along the length initially and at the tapered end of the wing it rises up. The pressure exerted by the air is given by P b is upward. The direction of air on the top or front part of the wing is shown as flowing along the length of the wing. The pressure exerted by the air is given by P f and it acts downward. Part b of the figure shows a boat with a sail. The direction of sail is almost across the boat. The direction of air in the sail is shown by lines on front and back sides of the sail. The air currents on the front exert a pressure P front toward the sail and air currents on the back sides of sail exerts a pressure P back again toward the sail.

Thus pressure P2P2 size 12{P rSub { size 8{2} } } {} over the second opening is reduced by 12ρv2212ρv22 size 12{ { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{2} } rSup { size 8{2} } } {}, and so the fluid in the manometer rises by h h on the side connected to the second opening, where

h12ρv22.h12ρv22. size 12{h prop { {1} over {2} } ρv rSub { size 8{2} } rSup { size 8{2} } "."} {}
(12)

(Recall that the symbol size 12{ prop } {} means “proportional to.”) Solving for v2v2 size 12{v rSub { size 8{2} } } {}, we see that

v2h.v2h. size 12{v rSub { size 8{2} } prop sqrt {h} "."} {}
(13)

Figure 4(b) shows a version of this device that is in common use for measuring various fluid velocities; such devices are frequently used as air speed indicators in aircraft.

Figure 4: Measurement of fluid speed based on Bernoulli’s principle. (a) A manometer is connected to two tubes that are close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, and so the fluid has a speed v v across the opening; thus, pressure there drops. The difference in pressure at the manometer is 12ρv2212ρv22 size 12{ { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{2} } rSup { size 8{2} } } {}, and so h h is proportional to 12ρv2212ρv22 size 12{ { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{2} } rSup { size 8{2} } } {}. (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
Part a shows a U-shaped manometer tube connected to ends of two tubes which are placed close together. Tube one is open on the end and shows a velocity v one equals zero at the end. Tube two has an opening on the side and shows a velocity v two across the opening. The level of fluid in the U-shaped tube is more on the right side than on the left. The difference in height is shown by h. Part b of the figure shows a velocity measuring device a pitot tube. Two coaxial tubes, one broader outside and other narrow inside are connected to a U-shaped tube. The U-shaped tube is also narrow at one end and broader at the other. The narrow end of the U-shaped tube is connected to the narrow inner tube and the broader end of the U-shaped tube is connected to the broader outer tube. The tube one has an opening at one of its edges and the velocity of the fluid at the end is v one equals zero. Tube two has an opening on the side and shows a velocity v two across the opening. The level of fluid in the U-shaped tube is more on the right side than on the left. The difference in height is shown by h.

Summary

  • Bernoulli’s equation states that the sum on each side of the following equation is constant, or the same at any two points in an incompressible frictionless fluid:
    P1+12ρv12+ρgh1=P2+12ρv22+ρgh2.P1+12ρv12+ρgh1=P2+12ρv22+ρgh2. size 12{P rSub { size 8{1} } + { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{1} } rSup { size 8{2} } +ρ ital "gh" rSub { size 8{1} } =P rSub { size 8{2} } + { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{2} } rSup { size 8{2} } +ρ ital "gh" rSub { size 8{2} } } {}
    (14)
  • Bernoulli’s principle is Bernoulli’s equation applied to situations in which depth is constant. The terms involving depth (or height h ) subtract out, yielding
    P1+12ρv12=P2+12ρv22.P1+12ρv12=P2+12ρv22. size 12{P rSub { size 8{1} } + { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{1} } rSup { size 8{2} } =P rSub { size 8{2} } + { { size 8{1} } over { size 8{2} } } ρv rSub { size 8{2} } rSup { size 8{2} } } {}
    (15)
  • Bernoulli’s principle has many applications, including entrainment, wings and sails, and velocity measurement.

Conceptual Questions

Exercise 1

You can squirt water a considerably greater distance by placing your thumb over the end of a garden hose and then releasing, than by leaving it completely uncovered. Explain how this works.

Exercise 2

Water is shot nearly vertically upward in a decorative fountain and the stream is observed to broaden as it rises. Conversely, a stream of water falling straight down from a faucet narrows. Explain why, and discuss whether surface tension enhances or reduces the effect in each case.

Exercise 3

Look back to Figure 1. Answer the following two questions. Why is PoPo size 12{P rSub { size 8{o} } } {} less than atmospheric? Why is PoPo size 12{P rSub { size 8{o} } } {} greater than PiPi size 12{P rSub { size 8{i} } } {}?

Exercise 4

Give an example of entrainment not mentioned in the text.

Exercise 5

Many entrainment devices have a constriction, called a Venturi, such as shown in Figure 5. How does this bolster entrainment?

Figure 5: A tube with a narrow segment designed to enhance entrainment is called a Venturi. These are very commonly used in carburetors and aspirators.
Figure shows a venturi tube, a cylindrical tube broader at both the ends and narrow in the middle. The narrow part is labeled as venturi constriction. The flow of fluid is shown as horizontal arrows along the length of the tube toward the right. The flow lines are closer in the center and spread apart at both the ends. There is an opening on the top portion of the narrow section for the entrained fluid to enter.

Exercise 6

Some chimney pipes have a T-shape, with a crosspiece on top that helps draw up gases whenever there is even a slight breeze. Explain how this works in terms of Bernoulli’s principle.

Exercise 7

Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.

Exercise 8

Why is it preferable for airplanes to take off into the wind rather than with the wind?

Exercise 9

Roofs are sometimes pushed off vertically during a tropical cyclone, and buildings sometimes explode outward when hit by a tornado. Use Bernoulli’s principle to explain these phenomena.

Exercise 10

Why does a sailboat need a keel?

Exercise 11

It is dangerous to stand close to railroad tracks when a rapidly moving commuter train passes. Explain why atmospheric pressure would push you toward the moving train.

Exercise 12

Water pressure inside a hose nozzle can be less than atmospheric pressure due to the Bernoulli effect. Explain in terms of energy how the water can emerge from the nozzle against the opposing atmospheric pressure.

Exercise 13

A perfume bottle or atomizer sprays a fluid that is in the bottle. (Figure 6.) How does the fluid rise up in the vertical tube in the bottle?

Figure 6: Atomizer: perfume bottle with tube to carry perfume up through the bottle. (credit: Antonia Foy, Flickr)
A perfume bottle with a spray cap.

Exercise 14

If you lower the window on a car while moving, an empty plastic bag can sometimes fly out the window. Why does this happen?

Problems & Exercises

Exercise 1

Verify that pressure has units of energy per unit volume.

Solution

P = Force Area , ( P ) units = N/m 2 = N m/m 3 = J/m 3 = energy/volume P = Force Area , ( P ) units = N/m 2 = N m/m 3 = J/m 3 = energy/volume alignl { stack { size 12{P= { {"Force"} over {"Area"} } ,} {} # size 12{ \( P \) rSub { size 8{"units"} } ="N/m" rSup { size 8{2} } =N cdot "m/m" rSup { size 8{3} } ="J/m" rSup { size 8{3} } } {} # ="energy/volume" {} } } {}

Exercise 2

Suppose you have a wind speed gauge like the pitot tube shown in Figure 4(b). By what factor must wind speed increase to double the value of hh size 12{h} {} in the manometer? Is this independent of the moving fluid and the fluid in the manometer?

Exercise 3

If the pressure reading of your pitot tube is 15.0 mm Hg at a speed of 200 km/h, what will it be at 700 km/h at the same altitude?

Solution

184 mm Hg

Exercise 4

Calculate the maximum height to which water could be squirted with the hose in Example 1.2 example if it: (a) Emerges from the nozzle. (b) Emerges with the nozzle removed, assuming the same flow rate.

Exercise 5

Every few years, winds in Boulder, Colorado, attain sustained speeds of 45.0 m/s (about 100 mi/h) when the jet stream descends during early spring. Approximately what is the force due to the Bernoulli effect on a roof having an area of 220m2220m2 size 12{"220"`m rSup { size 8{2} } } {}? Typical air density in Boulder is 1.14kg/m31.14kg/m3 size 12{1 "." "14"`"kg/m" rSup { size 8{3} } } {}, and the corresponding atmospheric pressure is 8.89×104N/m28.89×104N/m2 size 12{8 "." "89" times "10" rSup { size 8{4} } `"N/m" rSup { size 8{2} } } {}. (Bernoulli’s principle as stated in the text assumes laminar flow. Using the principle here produces only an approximate result, because there is significant turbulence.)

Solution

2 . 54 × 10 5 N 2 . 54 × 10 5 N size 12{2 "." "54" times "10" rSup { size 8{5} } " N"} {}

Exercise 6

(a) Calculate the approximate force on a square meter of sail, given the horizontal velocity of the wind is 6.00 m/s parallel to its front surface and 3.50 m/s along its back surface. Take the density of air to be 1.29 kg/m31.29 kg/m3 size 12{1 "." "29"`"kg/m" rSup { size 8{3} } } {}. (The calculation, based on Bernoulli’s principle, is approximate due to the effects of turbulence.) (b) Discuss whether this force is great enough to be effective for propelling a sailboat.

Exercise 7

(a) What is the pressure drop due to the Bernoulli effect as water goes into a 3.00-cm-diameter nozzle from a 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? (b) To what maximum height above the nozzle can this water rise? (The actual height will be significantly smaller due to air resistance.)

Solution

(a) 1.58×106 N/m21.58×106 N/m2 size 12{1 "." "58" times "10" rSup { size 8{6} } " N/m" rSup { size 8{2} } } {}

(b) 163 m

Exercise 8

(a) Using Bernoulli’s equation, show that the measured fluid speed vv for a pitot tube, like the one in Figure 4(b), is given by

v=2ρghρ1/2,v=2ρghρ1/2, size 12{v= left ( { {2 { {ρ}} sup { ' }gh} over {ρ} } right ) rSup { size 8{ {1} slash {2} } } } {}
(16)

where hh size 12{h} {} is the height of the manometer fluid, ρρ size 12{ { {ρ}} sup { ' }} {} is the density of the manometer fluid, ρρ size 12{ρ} {} is the density of the moving fluid, and gg size 12{g} {} is the acceleration due to gravity. (Note that vv size 12{v} {} is indeed proportional to the square root of hh size 12{h} {}, as stated in the text.) (b) Calculate vv size 12{v} {} for moving air if a mercury manometer’s hh size 12{h} {} is 0.200 m.

Glossary

Bernoulli’s equation:
the equation resulting from applying conservation of energy to an incompressible frictionless fluid: P + 1/2pv2 + pgh = constant , through the fluid
Bernoulli’s principle:
Bernoulli’s equation applied at constant depth: P1 + 1/2pv12 = P2 + 1/2pv22

Content actions

Download module as:

Add module to:

My Favorites (?)

'My Favorites' is a special kind of lens which you can use to bookmark modules and collections. 'My Favorites' can only be seen by you, and collections saved in 'My Favorites' can remember the last module you were on. You need an account to use 'My Favorites'.

| A lens I own (?)

Definition of a lens

Lenses

A lens is a custom view of the content in the repository. You can think of it as a fancy kind of list that will let you see content through the eyes of organizations and people you trust.

What is in a lens?

Lens makers point to materials (modules and collections), creating a guide that includes their own comments and descriptive tags about the content.

Who can create a lens?

Any individual member, a community, or a respected organization.

What are tags? tag icon

Tags are descriptors added by lens makers to help label content, attaching a vocabulary that is meaningful in the context of the lens.

| External bookmarks